Understanding Plumbing Basics for Bathtub Installation
Understanding Plumbing Basics for Bathtub Installation
Blog Article
Nearly everybody will have their own individual rationale in relation to How to Install a Bathtub Yourself.
Mounting a tub isn't specifically rocket science, however it does call for solid plumbing, woodworking, as well as in some cases, tiling skills. Replacing an old bathtub with a new one is additionally a reasonably difficult job. If the old tub is conveniently accessible, the task can move speedily; if you have to open a wall to remove the old bathtub as well as place the new bath tub, the task is a lot harder. In either situation, the task is within a house handyman's abilities, although you will certainly require a helper to move out the old bathtub and embeded in the new one. Make sure you have actually certified yourself for the work and also are comfortable trying it. As opposed to employing a professional to take over a halfway-completed job, it is much better to think about utilizing one prior to you begin. Opportunities are you may need an expert plumber to make tube links.
This write-up will help you mount a new bathtub in your shower room if you have actually already acquired a new tub and also do not require to alter the arrangement of your previous water pipelines.
Your tools and material checklist ought to comprise the following:
Preparing for the Installation
First of all, the supporting structure supplied with the bathroom needs to be fitted (if called for) according to the producer's directions. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is very important to make sure that if the tap features a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps device to prevent strain on the bath tub.
Fit the flexible tap connectors to the bottom of both faucets utilizing 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet via the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make certain you utilize every one of the supplied washers.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath ought to currently be ready to be fitted in its last position.
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your setup, then the first thing you must do is separate the water supply. After doing so, turn on the taps to drain pipes any water remaining in the system. The procedure of getting rid of the existing faucets can be quite troublesome because of the limited accessibility that is usually the case.
Use a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the taps. Have a cloth ready for the staying water that will certainly come from the pipes. Once the supply pipes have been removed, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary faucets from transforming during this process. When the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Prior to going on to fit the new taps, compare the pipeline links on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.
Mounting the Tub
Making use of the two wooden boards under its feet, place the bathtub in the needed position. The wood boards are handy in equally spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto 4 little factors.
The next goal is to ensure that the tub is leveled all round. This can be achieved by examining the level as well as readjusting the feet on the bathtub until the level reviews level.
To install taps, fit all-time low of the furthest adaptable faucet connector to the appropriate supply pipe by making a compression join; then do the exact same for the various other faucet.
Activate the water and also check all joints and also new pipework for leaks and also tighten them if required. Fill the bathtub as well as likewise check the overflow electrical outlet and also the regular electrical outlet for leakages.
Lastly, repair the bath paneling as explained in the maker's user's manual. Tiling and sealing around the bathtub ought to wait until the tub has actually been used at the very least when as this will certainly settle it into its last setting.
Fitting New Touches
If the tails of the new taps are plastic, then you will certainly require a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end offers a link to the existent supply pipes.
If you require to fit a monobloc, after that you will require lowering couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, position the tap in the mounting opening in the bath/basin making certain that the washers are in area between the faucet and the sink. Safeguard the faucet in position with the manufacturer supplied backnut. When the tap is safely in position, the supply pipes can be connected to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with normal faucet ports. The previous type needs to be connected to the tap ends first, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bath fulfills the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to crack an inflexible seal, creating the water to permeate the wall between the bath as well as the tiling, leading to problems with dampness as well as possible leakages to the ceiling below.
You can choose from a variety of coloured sealants to assimilate your components and installations. They are marketed in tubes and cartridges, as well as can sealing spaces as much as a width of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with twists of soaked paper or soft rope. Remember to constantly fill up the bathtub with water before sealing, to enable the activity experienced when the tub is in use. The sealant can split rather early if you do not take into consideration this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise quickly offered on the marketplace. It is recommended to fit the ceramic tiles using water-resistant or waterproof adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a keen person who reads about Installing A Bathtub, I thought sharing that piece of content was beneficial. Loved our entry? Please share it. Let another person check it out. Many thanks for going through it.
Real results? Dial! Report this page